Easy accessibility for maintenance

The washing machines for complex mechanical parts like the automobile cylinder block or cylinder heads are like machine tools with a lot of mechanics , hydraulics , pneumatics and electric components.

The reliability of the machine is directly linked with the good working of these components . These components are submitted to very bad conditions compared with a machine tool.Inside a washing machine there is a lot of bad conditions : dust air, humidity , temperature , vibrations, water spraying , chemicals( detergents) , coolants (coming with the parts to be washed) ,chips ,burrs ,.. The conditions are much worst than in a machine tool.

These conditions are very hard for the machine components and the engineering of a good washing machine has to consider as a first task to limit the components inside the washing machine.

This task is not always 100% possible and inside the machine there are also  mechanic components that have to be easy to maintain and repair. For this reason the second task of a good washing machine engineering is to take care of the accessibility to all the components around the machine.

Easy accessibility of the maintenance operator to all the components located outside the machine ( cylinders , mechanics, switches,valves, check valves , distributors…) and also to the inside the machine.

Depending of the machine size and the components inside the machine the accessibility can be made with large doors in order that the operator can access to the component keeping his foots outside the machine.

But in high production machines ,or big machines the operator has sometime to go inside the machine for the maintenance . For that, late 70’s the company Agullo launch a big innovation . A complete wall of the machine , all along the machine was a door with a vertical opening( big size guillotine door). The door received different names trough the times , vertical door , vertical guillotine door , full access side door, full size door … and was rapidly adapted by others manufacturers .

The first installations with these full size guillotine doors we supplied by Agullo to Peugeot and Renault in France . They were driven by a motoreducer and two chains on the top. The door opening was from the roof till the transfer .

The french competitor Stic Hafroy seen the machines in Peugeot and Renault quickly “adopted” this type of door in their machines.

The dimensions for the doors were growing in length (machines with 12mts doors length) and in heigth allowing to the operator to go and walk  inside the machine . Normally the machines were equipped with only one door in one side of the machine , but Agullo supplied also machines with two doors one in each side of the machine.

 

 

 

 

 

As one of the main customers was Ford Motor co. in UK and Germany the competitors in these countries also adopted the full size access door ( Harry Major  , Beys…).

 

 

 

Harry Major

 

In Italy for Fiat the machines had one full size guillotine door in one side of the machine and one corridor all along the machine in the other side allowing the operators to walk all along the machine both sides of the transfer.Seen the machines supplied to FIAT the local competitors Tecnofirma , and ICOM incorporated the door to their machines.

Agullo

 

 

 

 

 

Icom

 

Tecnofirma

 

 

The driving of these doors was progressing from the double chain and one reductor , to the rack and pinion , or gear and pinion and from the top driving to the floor driving , always by cost reduction reasons because the safety was never a concern .

In the 90’s  and 2000’s a lot of machines were supplied to Ford , Chrysler and GM  USA with these doors been accepted on all the customers safety standards.

 

Agullo-Dürr Ecoclean

 

 

                         Agullo/Dürr Ecoclean

 

 

 

In USA the full size guillotine door was also adapted by competitors like Valiant

 

Valiant

 

 

The challenge of these doors is not only the mechanics for the vertical movement for open/close the door but the water leaks and the noise contention. Any small gap on the adjustment to the machine wall could allow the water leaks outside the machine or to rise the machine noise level. The door construction, the materials used, and the design allows to avoid all those problems.

The high production machining lines in the automotive industry needs high efficiency and reduced cost. Few operators are operating the machining lines , and the first maintenance task are made by themselves . The machine needs to be easily controlled , and maintained . The design of the machine has to take in consideration the easy access to all the machine components , the easy and quick dis-assembly and repair . Full access , illumination , clean air, clean access .

Don’t forget : The washing machine needs maintenance because they work on worst conditions than the machine tools. It is a supplier task to reduce the maintenance time needed and also to allow the easy maintenance.